Leica Geosystems - Incident Mapping Suite
Importing Pix4D data into IMS Map360
Posted by James Johnston on 17 December 2018 02:18 PM

 Best Practises for working with Pix4D, Evidence Recorder and IMS Map360 to incorporate Photogrammetry derived data into a Forensic Diagram.

Important Note: Pix4D, IMS Map360 and Evidence Recorder can collect data which can be merged into a single Map360 project.  The user must select appropriate settings with regards to Units (Feet, US Feet, or Meters) and the Mapping Coordinate system.  This guide will step you through the process.

• Your UAV may require you to select a coordinate system to be used for Geotagging.  This coordinate system can differ from the Export and Project Coordinate Systems.
• The coordinate system and units must be the same during the following three stages of the process:

  1. Collecting Ground Control Points and any additional points and linework when using Evidence Recorder and a GPS Receiver (IF you are exercising this additional option)
  2. Setting the Export Coordinate System in Pix4D
  3. Setting the Project Coordinate System in IMS Map360

• Refer to your local surveying authority or use this map to determine which coordinate systems are valid for your geographical region.  Once you have selected a system you will probably continue to use the same one as long as you are working in the same region.


In the Field

Importing Imagery

Setting the Output Coordinate System in Pix4D

Importing a New Coordinate System in Pix4D

Setting Ground Control Points in Pix4D

Processing imagery in Pix4D

The Results

Creating an IMS Map360 Scene

Assigning units and a coordinate system

Start Cyclone Step 1

Start Cyclone Step 2

Create Database

Import las file

Import Cyclone

Import Orthomosaic


In the Field

1. Perform fieldwork to collect imagery and, if required, ground control points on visible ground targets.  A UAV and Terrestrial Cameras can be used to create imagery.  Evidence Recorder and an RTK GPS system can be used to collect Ground control points that match painted targets that were included in the photographs.  Evidence Recorder can also be used to measure points and linework for other details that you need to include in your map but are concerned will not be visible from the photographs.

Back to Top

In Pix4D

2. Create a new Pix4D project:

3. Add Images to your project:


Note the Image Coordinate System shown above, this is the system by which geotags are interpreted.  These may be WGS84, UTM or ITRF.  It is dependent on your drone or camera settings.  This coordinate system may differ from your Ground Control File coordinate and unit Settings or your Output coordinate and unit Settings without adversely affecting your results.

Back to Top

5. Next, set your Output Coordinate System from the Project Menu:

6. The output coordinate system, plus the units setting, must match those set (or about to be set) in IMS Map360.  Select Feet or Meters FIRST, then you will be presented with a list of available systems in the “Known Coordinate System” field.  In this example we are selecting the Missouri West system in feet:

 Importing a Coordinate System

If you don’t see your required coordinate system:
Select “From EPSG” and and find your coordinate system on the Spatial Reference website.  Download a prj file and consult your Pix4D documentation

 See this article for guidance importing a coordinate system.

 Back to Top

7. Pick Finish

 Back to Top

8. If you need to incorporate a GCP file you must select units and a system that matches the one used by Evidence Recorder AND the Output System that you have already defined:

9. Use the dialog below to ensure that you have assigned the same Coordinate system and units for both GCP and Output Coordinate System:



See this video for a guide to importing a GCP


See this article for a guide on exporting a GCP from Evidence Recorder

 Back to Top


 10. See below for some recommended configurations for Processing options:








11. Now we can start Processing.


12. Turn off options 2 and 3 for the first stage and then "Start"

14. This will take a while.  When complete, examine the Processing Report.  If the results look good, check on Options 2 and 3 and pick “Start” to complete the creation of a pointcloud and orthomosaic.

Back to Top


15. The Result:

Back to Top

16. Importing the pointcloud, or LAS file into your Map360 project:

In IMS Map360


17. Open or create the drawing which you intend to import the Pointcloud data into.

Back to Top


18. Set the Scene Defaults:

 Back to Top

20. Start "Import Cyclone" command from the Import/Export or PointCloud ribbons.

21. This will make a connection to the EpcA engine and connect IMS Map360 to Cyclone.

You’ll see a progress bar for several seconds while it establishes this connection. When the Import ModelSpace dialog appears you may cancel the import command, but it's not mandatory:


You must now leave Map360 running in the background.

 Back to Top

In Cyclone

23. Run Cyclone. (A free "Viewer" installation is fine, license not required.)

If you see this prompt when you launch Cyclone simply pick "No" to enable free viewer mode


24. Expand “SERVERS” in the tree

25. Right-click on the “YOURCOMPUTERNAME (unshared)” database:

Back to Top


26. Click the “Add” button


27. …and browse to the location Pix4D has created your LAS file.

Look in: (Pix4D project location)\raw_files\2_densification\point_cloud


29. Enter a name for your Cyclone Database (IMP) file and Pick "Open" twice:


30. Select "OK"


31. The new database is added to the list, make sure it’s checked and click Close.


32. In the Cyclone Navigator, right-click on your new database and select “Import”


33. Browse to your .las file and open it.


It may take some time to import, depending on how big the scan is.
34. Expand your database, and you’ll see a new “ModelSpace”.


35. Close Cyclone

Back to Top

In IMS Map 360

36. Return to your drawing in IMS Map360.  Use the “Open Cyclone” command on the Import/Export tab (Sketch mode) or on the PointCloud tab (Advanced mode) or type CWIMPORT at the commandline.

37. ALWAYS set the units to Meters when working with Pix4d, and pick on "..." to start the import.


38. Expand the Database tree as shown to find your database the model space view to import, and select "Open."

NOTE: older versions of Cyclone required you to right click and create a modelspace view at this point, which you could then expand and "Open."




Pick on "OK"

40. Select Open

41. Your Pointcloud is imported.

If all procedures have been followed correctly any data collected using GPS and the pointcloud will align with each other.

Back to Top

Importing the Orthomosaic

42. Import the Orthomosaic file found in the dsm_ortho folder:

Look in: (Pix4D project location)\raw_files\3_dsm_ortho

See Here for a guide to importing the Orthomosaic file









(1 vote(s))
Not helpful

Comments (0)
Post a new comment
Full Name: